Engraving machine tool use the matters needing attention (woodworking engraving machine)

 

Engraving machine tool use should pay attention to what place?Here is our economic CNC equipment co., LTD. Nathan engineer according to carving machine use process summed up experience, to share with you.

 

1. Woodworking engraving machine in use process should pay attention to: the jacket size to fit, cross section, not enough round, wear, inner hole taper collet must not choose, or it will cause the handle vibration, carving out the ideal effect.

 

2. Woodworking engraving machine in use process should pay attention to: the handle and jacketed contact with moderate, insert the collet and tighten the handle is strong, if time is too long jacket used inner hole deformation, clamp must be replaced immediately.

 

3. Woodworking engraving machine in use process should pay attention to: tool cannot be polished or change their form.

 

4. Woodworking engraving machine in use process should pay attention to: rough machining such as particieboard is recommended to use more stripes milling cutter.

 

5. Wood carving machine in use process should pay attention to: cutter always checker toughness, if using a blunt, please replaced immediately, if continue to use not only engraving effect is not good, also the cutting knife will happen.

 

6. Woodworking engraving machine in use process should pay attention to: the use effect of incised knife, processing product surface without burr, won't become warped plate processing.

 

7. Woodworking engraving machine in use process should pay attention to: multilayer board, plywood processing, recommend using double straight slot milling cutter.

 

8. Woodworking engraving machine in use process should pay attention to: the thickness of no more than can the thickness of the cutting edge, responsible for still can appear broken sword.

 

9. Woodworking engraving machine in use process should pay attention to: the cutting of different material, should use reasonable cutting speed.

 

10. Woodworking engraving machine in use process should pay attention to: in body, clothes, hair, shall not be close to the work object.

 

11. Woodworking engraving machine in use process should pay attention to: recommend cutting speed to keep balance, speed consistent as far as possible, in order to achieve better results, cutting too long can't stay, the same to.

 

12. Woodworking engraving machine in use process should pay attention to: aluminum plate cutting processing, recommend using single blade special aluminum with milling cutter.Non-stick knife in the processing, speed, high efficiency.

 

13. Woodworking engraving machine in use process should pay attention to: the density board cutting processing, recommend using claymore chip spiral milling cutter, it has two high-capacity chip groove, double edge design, both has the very good chip removal function, and achieve a good balance tool, in processing high density board, not black, no cap smoke, long service life, etc.

 

14. Woodworking engraving machine in use process should pay attention to: cutting tools with special detergent to remove dirt.

 

15. Woodworking engraving machine in use process should pay attention to: butter can prevent knives rust.

 

16. Woodworking engraving machine in use process should pay attention to: acrylic mirror sculpture processing is recommended to use diamond graver.

 

17. Woodworking engraving machine in use process should pay attention to: high density board, wood is recommended to use edge milling cutter.

 

18. Woodworking engraving machine in use process should pay attention to: on the following burr-free cutting processing, recommend using single blade and double incised on the cutter.

 

19. Woodworking engraving machine in use process should pay attention to: cork, density board, the original wood, PVC, acrylic large deep anaglyph processing, recommend using single blade helical ball end milling cutter.

 

20. Woodworking engraving machine in use process should pay attention to: precision small anaglyph processing, recommend using round bottom knives.

 

21. Woodworking engraving machine in use process should pay attention to: the force that press a gram cutting processing, recommend using single blade spiral milling cutter, characterized by processing the smokeless tasteless, quick speed, high efficiency, non-stick crumbs, real environmental protection, the special manufacturing process to ensure that processing the force that press a gram not mouth, very fine grain (or even no knife), the surface is bright and clean level off.Machining surface to achieve frosted effect, it is recommended to use double three blade spiral milling cutter.